One Stop Epoxy Self Leveling 100% Solids Epoxy is a professional-grade, two-component, high-build epoxy resin designed for industrial, commercial, and decorative flooring systems.

Its 100% solids by volume formulation contains no water or added solvent that must evaporate during curing, allowing the applied material to maintain substantial film thickness. It can be used as a solid-color body coat, receiver coat for decorative flakes or quartz, commercial epoxy layer, or uniform base coat beneath metallic epoxy flooring systems.

• 100% solids epoxy by volume
• Professional two-component system
• Self-leveling formulation
• High-build coating
• 3-gallon mixed kit
• 2:1 mixing ratio
• Suitable for industrial and commercial flooring
• Compatible with flake, quartz, and sand broadcast systems
• Suitable as a base coat for selected metallic epoxy systems
• Available in multiple colors

Applications

Suitable for a wide range of flooring systems and environments, including:

• Warehouses
• Garages
• Workshops
• Showrooms
• Commercial interiors
• Industrial floors
• Solid-color epoxy floors
• Partial and full flake flooring systems
• Quartz and sand broadcast systems
• Base coats for metallic epoxy flooring

The manufacturer specifically identifies garages, shops, warehouses, showrooms, and commercial interiors among the applications for its high-build solid-color epoxy body coat.

Technical Specifications

• Brand / Product Line: One Stop Epoxy
• Product: Self Leveling 100% Solids Epoxy
• Type: Self-Leveling Epoxy Resin
• Components: Two-Part – Part A + Part B
• Solids by Volume: 100%
• Kit Size: 3 Mixed Gallons
• Mix Ratio: 2 Parts A : 1 Part B by Volume
• Mixed Viscosity: 500–750 cps
• Shore D Hardness: 89–91
• Compressive Strength: 16,500 psi
• Tensile Strength: 3,850 psi
• Adhesion to Concrete: 600 psi
• Flexural Modulus: 4,700 psi
• Taber Abrasion: 22 mg Loss
• VOC: Less than 50 g/L

Available Colors

Clear • Light Gray • Medium Gray • White • Tan • Black

The colored versions are supplied pre-pigmented, with the pigment already incorporated into Part A.

Approximate Coverage

Coverage depends on the flooring system and required film thickness:

• Flake Receiver Coat: 133–150 ft²/gallon, or approximately 399–450 ft² per 3-gallon kit
• Higher-Build Solid Color / Commercial Coat: 100–135 ft²/gallon, or approximately 300–405 ft² per kit
• Metallic Epoxy Base Coat: 135–150 ft²/gallon, or approximately 405–450 ft² per kit

Working & Cure Times

At approximately 75°F (24°C):

• Bucket Time: Approx. 8 minutes
• Floor Working Time: Approx. 45 minutes
• Tack-Free: Approx. 8–10 hours
• Recoat Window: Approx. 12–24 hours
• Light Foot Traffic: Approx. 24 hours
• Heavy Foot Traffic: Approx. 48 hours
• Vehicle Traffic: Approx. 72 hours
• Full Chemical Cure: Approx. 7 days

Higher temperatures shorten the available working time.

Surface Preparation & Application

Concrete must be properly cleaned, repaired, mechanically prepared, vacuumed, and evaluated for moisture before application. The product's self-leveling properties help the resin flow and settle after spreading but do not eliminate the need for proper concrete preparation or repair of cracks and surface defects.

For a full 3-gallon kit, Part A should be premixed before adding all of Part B. The complete mixture should then be mixed for approximately 2 minutes at 300–450 RPM using a suitable cage- or box-style mixer and immediately poured onto the prepared floor.

Important: This epoxy should not be used as an exposed exterior finish because direct sunlight can cause ambering. Exterior systems require appropriate UV-resistant protection.